Authorized Dealer of FESTO / Pneumatic and Electrical Automation
+91 99799 48222 +91 98799 59951 | info@primeintl.in
-
Axis controller CPX-CMAX-C1-1
- Pneumatic positioning and force control
- A technology module of the terminal CPX
- Can be used with all fieldbus interfaces CPX, as well as Ethernet
- Easy commissioning with Festo configuration tool FCT
- Automatically detects connected system components: valve VPWP, sensor interface CASM or the cylinder
- Moves loads of 2 to 450 kg
- Controls forces between 30 and 4712 N
-
Connecting cable KMPYE
- For solenoid coils with thread M12x1 A-coded according to EN 61076-2-101
- For connecting proportional directional control valves MPYE with end-position controller SPC11
- Cable length 0.3 … 5 m
- With PVC or PUR cable
- Ambient temperature -25 … +80 °C
-
Connecting cable KVI
- For fieldbus connection with thread M9x0.5
- Connecting cable between valve terminal and controller
- Connecting cable between valve terminal and input/output modules
- Connecting cable between controller and input/output modules
- Pre-assembled at both ends
- Suitable for use with energy chains
- Cable length 0.25 … 8 m
- With PUR cable
- Ambient temperature -20 … +80 °C
-
Displacement encoder MLO-POT-LWG
- Connecting rod potentiometer
- Absolute measurement with high resolution
- Long service life
- Degree of protection IP65
- Plug-in connections
-
Displacement encoder MLO-POT-TLF
- Conductive plastic potentiometer
- Absolute measurement with high resolution
- High travel speed and long service life
- Plug-in connections
-
Displacement encoder MME-MTS-TLF
- Measuring principle: magnetostrictive
- Contactless with absolute measurement
- High travel speed
- System product for servo-pneumatic positioning technology and Soft Stop
- Degree of protection IP65
-
End position controller CPX-CMPX-C-1-H1
- End positions with 2 additional, freely selectable intermediate positions
- Electronic end-position control for pneumatic drives
- Soft-stop for gentle deceleration and fast acceleration
- Use with all fieldbuses available for CPX/Ethernet
- and controllers FEC
- Simple commissioning, Festo plug & work®
- Travel times and air consumption roughly 30% less than comparable standard pneumatics
-
End-position controller SPC11
- Quickly and smoothly into the end position with 2 additional intermediate positions
- Electronic end-position cushioning
- Quick and easy commissioning: configure, teach, done
- Supports pneumatic drives with piston rod, rodless drives and semi-rotary drives
-
Linear actuator with displacement encoder DFPI
Easy to install, sturdy and reliable in use, the corrosion-resistant linear actuator DFPI to ISO 15552 has a built-in linear potentiometer or fully integrated positioner.
- Mounting interfaces to ISO 15552
- Sturdy tie rod design
- Integrated air supply
- Optionally with integrated displacement encoder or fully integrated positioner
- IP65, IP67, IP69K, NEMA4
- ATEX certification
-
Linear drive with displacement encoder DGCI
Positioning drive with eccentric sealing system for practically leakage-free long strokes without restrictions and with displacement encoders using the non-contact measuring method.
- With guide
- With displacement encoder for absolute, contactless measurement
- Suitable for servo-pneumatic applications with axis controller CPX-CMAX, end-position controller CPX-CMPX or SPC11 and measuring module CPX-CMIX
- Choice of supply ports on end face or front
-
Measured-value transducer DADE
- For standards-based cylinders DNCI and DDPC
- Converts sensor signals into voltage or current signals
- Mounting via through-holes
-
Plug FBS-SUB
- Plug connector for CAN bus and PROFIBUS bus connection
- Cable connection 2x horizontal or 2x vertical
- PCB terminal block with screw connector